hopf 8029HEPTA-V2/GPS Technical Manual Download Page 15

Page: 15 / 130

YSTEM

TRUCTURE

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

15 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

2.2.3 Reset-(Default) Button

The Reset-(Default) Button is accessible with a thin object through the
small drilling in the front panel next to the "Reset" inscription" (see

Chapter 4.3 Reset-(Default) Button

2.2.4 NTP Status LEDs (NTP/Stratum/Accuracy)

NTP-LED (Green) NTP service of the Time Server

8029HEPTA/GPS

Standard

, running

Off

Not running

Stratum1-LED
(Green)

The NTP service of the Time Server
8029HEPTA/GPS works with:

Stratum 1

Flashes

Stratum 2-15

Off

Stratum 16 (no synchronization of NTP
Clients)

Accuracy-LED
(Green)

The NTP service of the Time Server
8029HEPTA/GPS works with accuracy of:

high

Flashes

medium

Off

low

2.2.5 USB-Port (Host)

On specific problems the USB connection can be used for a
system recovery after consulting the

hopf

Support.

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands

hopf 8029HEPTA-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands