hopf 8029HEPTA-V2/GPS Technical Manual Download Page 81 | Manualshive

Page: 81 / 130

background image

HTTP/HTTPS

W

EB

GUI

–

W

EB

B

ROWSER

C

ONFIGURATION

I

NTERFACE

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

81 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

8.3.4 ALARM Tab (Activation Key necessary)

All the links within the tab on the left hand side lead to corresponding detailed setting options.

8.3.4.1 Syslog Configuration

It is necessary to enter the name or IPv4 or IPv6 address of a Syslog server in order to store
every  configured  alarm  situation  which  occurs  on  the  module  in  a  Linux/Unix  Syslog.  If
everything  is  configured  correctly  and  enabled  (depending  on  the  Syslog  level),  every
message is transmitted to the Syslog server and stored in the Syslog file there.

Syslog uses Port 514.

Co-logging in the system itself is not possible as therefore the internal memory is not of
sufficient size.

It should be noted that the standard Linux/Unix Syslog mechanism is used for this functionality.
This is not the same as the Windows System Event mechanism!

The alarm level designates the priority level of the messages to be transmitted and the level
from which transmission should take place (see

Chapter 8.3.4.4 Alarm Messages

).

Alarm Level

Transmitted Messages

none

no messages

info

info / warning / error / alarm

warning

warning / error / alarm

error

error / alarm

alarm

alarm

The NTP service implemented in the system can transmit its own Syslog messages
(see

Chapter 8.3.3.4.2 NTP Syslog Messages (General / Log NTP Messages to Syslog)

).

«
...
79
80
81
82
83
...
»

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Reviews:

No comments

Related manuals for 8029HEPTA-V2/GPS

Brand: SEH Pages: 20

Brand: Fujitsu Pages: 111

Brand: Fujitsu Pages: 543

Brand: Aqua Medic Pages: 24

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 32

TX-28LD4DP:TX-25LD4DP

Brand: Panasonic Pages: 40

Brand: Panasonic Pages: 58

Brand: Panasonic Pages: 52

TH50PE77U - 50" HD PLASMA TV

Brand: Panasonic Pages: 62

Brand: Panasonic Pages: 112

SF4D-x-01 Series

Brand: Panasonic Pages: 176

Brand: Panasonic Pages: 220

Brand: Katsumi Pages: 3

Brand: Weather Guard Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands