hopf 8029HEPTA-V2/GPS Technical Manual Download Page 119

Page: 119 / 130

ACTORY

EFAULTS OF

IME

ERVER

8029HEPTA/GPS

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

119 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

13.1.3 ALARM

Syslog Configuration

Setting

WebGUI

Syslog

Disabled

Server Name

Blank

---

Alarm Level

Disabled

none

E-mail Configuration

Setting

WebGUI

E-mail Notifications

Disabled

SMTP Server

Blank

---

Sender Address

Blank

---

E-mail Addresses

Blank

---

SNMP Traps Configuration

Setting

WebGUI

SNMP Traps

Disabled

Alarm Level

Disabled

none

SNMP Trap Receivers

Blank

---

Alarm Messages

Setting

WebGUI

Alarms

all Disabled

all none

13.1.4 DEVICE

User Passwords

Settings

WebGUI

Master Password

master

---

Device Password

device

---

Diagnostic

Settings

WebGUI

Real Time Diagnostics

Disabled

Product Activation

Settings

WebGUI

Activate Feature

No changes

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands

hopf 8029HEPTA-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands