manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 517 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 517

REVISIONS

REV

DESCRIPTION

DATE

APP’D

C

ADB

Red (sensor power)

Violet (sensor 2)

1 - Sensor Power˜

3 - Sensor Input

Blue (sensor 6)

Brn (sensor 1)

Org (sensor 3)

Yel (sensor 4)

Grn (sensor 5)

Blk (Ground)

2 - Ground

4 - N/C

DiPro RCB

GND

1

2

3

4

5

6

1

2

3

4

THIS OUTPUT WILL TURN ON WHEN THE DIPRO

SENSORS ARE DISABLED.  IT IS AN OPEN COLLECTOR

TYPE OUTPUT AND CAN SINK 8 MA. TO GROUND.

302 (Relay Pwr)

282 (S

en 1)

283 (S

en 2)

284 (S

en 3)

285 (S

en 4)

286 (S

en 5)

287 (S

en 6)

288 (S

en 7)

289 (S

en 8)

290 (S

 P
w

r)

304 (Aux 3)

303 (Aux 4)

305 (Aux 2)

306 (Aux 1)

DiProPAC 8

291 (Grd)

1

1

12 VDC SOLID-STATE

+ INPUT

- INPUT

OUTPUT

OUTPUT

RELAY

DiProPAC to RCB Wiring Diagram

CUSTOMER SUPPLIED

any part thereof, any information contained therein or any physical article or    

thereof confers or transfers any right to reproduce or disclose the document,  

device, or to practice any method or process, except by written permission or

PROPRIETARY RIGHTS.  This document discloses subject matter in which
HONEYWELL has proprietary rights.  Neither receipt nor possession 

written agreement with HONEYWELL.

FIGURE 11

CODE IDENT NO.

DRAWING NUMBER

APPROVALS

HONEYWELL

ACTON MA.

FILENAME

DRAWN

TITLE

SHEET

SCALE

DATE

CHK.

ENG.

MFG.

SIZE

REV

REL

OF

7/18/03

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments