manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 41 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 41

SmartPAC 2 with WPC Integration

1126800

Introduction to SmartPAC 2 

Chapter 1

page 19

SmartPAC 2's Three Modes of Operation

You can do various things with SmartPAC 2 depending on the mode you are in.
•

Initialization Mode.

  Used to make settings that generally only need to be made once

after installation.  You can set cam names and lock out certain setting parameters.
Initialization mode is discussed in detail in 

Chapter 4

.

•

Program mode. 

Used to make your sensor and cam timing, counter, and other settings

(if installed) for your tools.  You cannot use this mode while the press is running. You
can load settings for a tool in this mode.  The displays you see in Program mode are
described in 

Chapter 5

.

•

Run Mode.

  You must be in Run mode to operate the press.  You can adjust timing for

your sensors and cam channels (if installed) while the press is running. You see
actuation angles for green sensors.  You can also load tool settings in Run mode.  The
settings you can make in Run mode are explained in 

Chapter 6

.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments