manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 327 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 327

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Program Mode

Chapter 5

page 305

View Cam Summary

To see the cam settings for the tool you are programming, in the Cam Program menu, Figure
5 - 27, press 

F6

-“View Cam Summary.”  A screen appears similar to the next figure,

showing channel number, cam name, type of timing and the timing settings..  The global
cams do not appear in this screen.

Figure 5 - 29.  Cam Summary

Make an ON/OFF Setting for a Channel

NOTICE

You can set multiple ON/OFF cycles for cam channels if you want.  See “Multiple ON/OFFs for

Cam Channels,” page 307.

1. Select a channel from the complete list (see previous figure). You will see the display

below. Notice that the tool number and channel name selected are shown in the display.
Select "Program on/off angle.”

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments