manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 141 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 141

SmartPAC 2 with WPC Integration

1126800

Installing SmartPAC 2 and WPC

Chapter 2

page 119

Top Stop Angle between 241

°°°°

 and 270

°°°°

:  Install Overrun Sensor Magnet

1.

 

Go to Initialization mode (page 203).  Select PRESS CONTROL. Select PRESS
OPTIONS. On the screen that appears, set Switches 1 and 2 as follows:

Switch 1 – CLOSED
Switch 2 – OPEN

To change a switch setting, highlight it and press ENTER to toggle between OPEN and
CLOSED.  Press RESET when done.

2.

 

Power down SmartPAC 2 with WPC and power it up again.  This makes the new switch
settings take effect.

3.

 

Go to Run mode and turn the Stroke Select key to OFF and then back to Inch to clear the
LOCKOUT message (see page 387).

4.

 

Go to Initialization mode. Select RESOLVER ZERO.  On the screen that appears, find
“Current Zero Correction.”  Write the Current Zero Correction here:  

 

_

              

°

  .

5.

 

Go to Table 2 - 13. Find the Current Zero Correction value in the appropriate column in
the table.  Circle the “Crankshaft Angle” next to it.

Table 2 - 13.  Top Stop Angle bet. 241

°°°°

 and 270

°°°°

:  Mounting Overrun Magnet

(Unzeroed Resolver Angle = 300

°

)

Zero Correction 0

°°°°

 - 30

°°°°

Zero Correction 330

°°°°

 - 359

°°°°

Current

Zero

Correction

Crankshaft

Angle on

Display

Current

Zero

Correction

Crankshaft

Angle on

Display

Current

Zero

Correction

Crankshaft

Angle on

Display

Current

Zero

Correction

Crankshaft

Angle on

Display

0

300

15

285

330

330

345

315

1

299

16

284

331

329

346

314

2

298

17

283

332

328

347

313

3

297

18

282

333

327

348

312

4

296

19

281

334

326

349

311

5

295

20

280

335

325

350

310

6

294

21

279

336

324

351

309

7

293

22

278

337

323

352

308

8

292

23

277

338

322

353

307

9

291

24

276

339

321

354

306

10

290

25

275

340

320

355

305

11

289

26

274

341

319

356

304

12

288

27

273

342

318

357

303

13

287

28

272

343

317

358

302

14

286

29

271

344

316

359

301

30

270

6.

 

Go to Run mode.  Turn the Stroke Select key to “Inch.”  Inch the press until the
SmartPAC 2 display shows the Crankshaft Angle you circled in Table 2 - 13.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments