manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 407 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 407

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Fault Messages

Chapter 7

page 385

What Happens When You Get a Fault Message

If an error or fault occurs, a red message box will appear, similar to the following, giving the
error code and a brief explanation of the error

Figure 7 - 2.  Error Code Box

If the press stops because one of the counter presets count is reached, a yellow message box
appears, similar to the following, telling which counter preset has been reached.

Figure 7 - 3.  Counter Preset Message Box

How to Clear the Fault Message from the Display

To resume operation after an error message

 

occurs, clear the error message by pressing the

RESET key (or Remote Reset Button, if installed).  Correct the malfunction or other problem

before

 running the press.

If you cannot correct the problem after reading the remedy, contact Wintriss Tech Support.

NOTICE

PROVIDE IMPORTANT INFORMATION WHEN CALLING WINTRISS TECH SUPPORT

When you contact Wintriss Controls for technical assistance, be ready to provide some
important information to expedite a resolution to the problem.  Please supply:  product name
(e.g. SmartPAC 2 standard); installed options (e.g. DiProPAC, ProCamPAC, etc.); and
firmware version number (e.g. Vs. 2.00).  You can determine the last two items, by going into
"Installed options" in the Initialization mode (see Chapter 4 for details).

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments