manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 474 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 474

1126800 

SmartPAC 2 with WPC Integration

page 452

Appendix B

SmartPAC Preventive Maintenance

(PM) Monitor

USE CURSOR KEYS TO CHANGE SELECTION
PRESS ENTER TO SELECT, RESET WHEN DONE

CLUTCH VALVE
   CHECK AT
   CURRENT

2000 STARTS/STOPS
1055 STARTS/STOPS

YOUR PRESS NAME
THERE IS 1 ITEM WITH ALERT STATUS

PM MONITOR

SLIDE ADJ. MOTOR
    CHECK AT
    CURRENT

100 DIE CHANGES

 101 DIE CHANGES

GIBS
   CHECK AT
   CURRENT

1000000 STROKES

558836 STROKES

MORE

PM Monitor alerts
you to check specific
item in "alert" status mode.
Notice "!!ALERT!!"
flashes.

CLEAR

ALERT

F3

CHANGE

VALUE

F4

shows how many alert
alert conditions are
current

!! ALERT!!

Figure B - 16.  Shows "Slide Adjust Motor" in "Alert" Mode

4. To view other items in the schedule that may or may not be in "alert" status, use the

cursor keys.  If more than three PM items were set in Initialization, they will not all
appear on the screen.  To view them, simply use the cursor keys to scroll down the list.

5. To clear the alert, first highlight that item, press the appropriate function key (designated

on your screen), and enter the PM password.

NOTICE

When you clear the alert condition for a certain item, you automatically reset its current value
to zero.  You cannot recall the previous value.

6. If you want to change the frequency value on a given PM item, first highlight that item,

press the designated function key, and enter the PM password.  The number display will
be superimposed over the screen (similar to Figure A-11).  Use the number keys or
cursor keys to modify the tracking frequency for that PM item.

7. After you are done viewing or modifying this screen, press RESET to return to the main

Run menu.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments