manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 280 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 280

1126800 

SmartPAC 2 with WPC Integration

Page 258

Chapter 4

SmartPAC 2 Initialization Mode

PACNET

(INITIALIZATION – PACNET)

Figure 4 - 39.  PACNet Set Communications Menu

If your SmartPAC 2 is connected to a Wintriss software product, in this screen you should set
the CPU number for this unit.  In addition, you set parameters relating to the PACNet
computerized pressroom reporting software.

The CPU number is from 1 to 99.  Make sure each control connected to the software has a
unique CPU number.  Select the value next to CPU NUMBER.  An entry box  appears.
Enter the CPU number using the number keys or the up and down cursor keys.

See your PACNet manual for more information about the items in this menu.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments