manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 268 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 268

1126800 

SmartPAC 2 with WPC Integration

Page 246

Chapter 4

SmartPAC 2 Initialization Mode

Switch 6 – Dual Light Curtain Enabled

NOTICE

After you change switch settings, power down the SmartPAC 2/WPC. Power it up again to
enable the new settings. If you do not this, the previous switch settings will remain in effect.

Set this switch to CLOSED if you have two light curtains connected to WPC.  Refer to
Figures 3 or 12 (for Herion valve) or Figure 5 (for Ross) to properly wire the dual light
curtains (end of this manual).

Set Switch 6 in the Press Control Option Switches screen, Figure 4 - 33, page 241.

Table 4 - 9.  Switch 6 Setting for Single or Dual Light Curtains

Option Switch 6 Setting

Light Curtain Configuration

OPEN

Single light curtain – normal operation

CLOSED

Dual light curtains enabled

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments