manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 337 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 337

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Program Mode

Chapter 5

page 315

TOOL INFORMATION

(PROGRAM – TOOL INFORMATION)

NOTICE

•

Tool Information serves only as a convenient place to record information about the tool.  It
does not control any aspect of press operation.

•

This feature is not available if you have the optional PLC interface installed.

Select “Tool Information” under the main Programming menu (Figure 5 - 3) to record useful
information about the tool you are programming.  See “Tool number information” in
Chapters 4 to set up the information items.

 

ENTER YOUR PASSWORD

USE THE  KEYPAD TO ENTER NUMBERS.
USE THE UP/DOWN CURSON KEYS TO
INCREASE/DECREASE. PRESS ENTER
WHEN DONE. PRESS RESET TO CANCEL.

    60599

If this display appears, you need to enter the general password to access these settings.  Password
access is set under Security Access in Initialization mode.  See 

“Security Access” in Chapter 4,

page 251

.

You will see a display similar to the following:

Use cursor
keys to
move
selection
bar to
desired
item. Press
ENTER.

                 TOOL NUMBER INFORMATION

PASS LINE HT                                IN
STRAIGHTENER                 4.25     IN
HYD. OVLD.                         100     TONS
PRESS SPEED                       65     SPM
CONVEYOR                           NO
PART LUBE                         YES

MEMO BOX
                                                              MEMO LINE 1
     CAREFULLY CHECK
     DIE PLACEMENT                            MEMO LINE 2

USE CURSOR KEYS TO CHOOSE THE VALUE YOU
WANT TO CHANGE. PRESS THE ENTER KEY TO
CHANGE IT. PRESS RESET KEY WHEN DONE.

F4

F5

4.50

Figure 5 - 39.  Tool Number Information Screen

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments