manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 304 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 304

1126800 

SmartPAC 2 with WPC Integration

page 282

Chapter 5

SmartPAC 2 Program Mode

Copy an Existing Tool

(PROGRAM – GO TO THE TOOL MANAGER – 

F8

-COPY TOOL)

1.

 

Use the cursor keys to highlight the tool on the Tool Manager   display (Figure 5 - 4) that
you want to copy.   In this example, tool #6162, “Bracket 2” is highlighted.  If there is a
large number of tools in SmartPAC 2’s memory, there will be additional columns.  Press
the left or right cursor keys to access the additional columns.

2.

 

Press 

F8

-“Copy Tool.”

3.

 

Enter the tool number in the box that appears (see Chapter 3 for instructions on entering
numbers and text).

4.

 

Go to “Tool Program Menu,” page 285, and program the tool.

Change Settings for an Existing Tool

(PROGRAM – GO TO THE TOOL MANAGER – select tool number)

DANGER

!

ANCILLARY EQUIPMENT MAY OPERATE WHEN TOOL IS LOADED

Ensure that all personnel stand clear when you load a tool.

Failure to comply with these instructions will result in death or serious injury.

1.

 

On the Tool Manager display (next figure)  use the cursor keys to highlight the tool you
want to make changes to.   In this example, tool #6162 is highlighted.  If there is a large
number of tools in SmartPAC 2’s memory, there will be additional columns.  Press the
left or right cursor keys repeatedly to access the additional columns.

F1

F2

F3

F4

F5

F6

F7

F8

Figure 5 - 9.  Tool Manager

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments