manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 360 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 360

1126800 

SmartPAC 2 with WPC Integration

Page 338

Chapter 6

SmartPAC 2 Run Mode

For HELP press the HELP key located at the center of the cursor (arrow) keys.

NOTICE

To e-mail a copy of this screen, see “Screen Capture,” page 199.

Show Sensor Status

(RUN – DIE PROTECTION– Select Sensor – 

F7

-SHOW SENSOR STATUS)

To access "Sensor Status,” first select "Die Protection" from the Main Run menu and you
will see a list of sensors.  Press the 

F7

 function key for "Show sensor status" which allows

you to see the status of all your sensors at once while the press is running or stopped.
The following display shows the status of every sensor for a loaded tool number. The sixteen
sensor inputs are indicated by the numbers 1 through 8, and 9 through 16 (if installed).  The
type of sensor connected to each input is indicated by the letters (and/or numbers) under the
numbered inputs.  G = green;  GCON = green constant;  RED is a red sensor; GQC = green
quick check; YEL = yellow; GS = green special (11 represents maximum number of strokes
allowed); N/U = not used.  If the square actuation block representing the sensor is dark, this
indicates that the sensor is actuated.

SENSOR STATUS

PRESS THE RESET KEY WHEN DONE.

CAMBIE

AL ESPANOL

PRESS #14

TOOL NUMBER  6160

PART CNTR 51635

FLANGE

TWO HAND CONT
PRESS SPEED 67

RETURN TO
MAIN MENU

3

RED

7

GQC

4

G

8

G

1

G

6

G

2

G

5

GCONS

10

YEL

9

GS 5

11

12

N/U

13

N/U

14

N/U

15

N/U

16

N/U

X indicates

sensor is

turned off

White actuation block

indicates sensor is

ungrounded

Black actuation block

indicates sensor is

grounded

Color indicates

type of sensor

(green, red, yellow)

Gray indicates not-used

(unprogrammed) sensors

Number indicates

maximum number

of strokes allowed

for Green Special

GCONS

Figure 6 - 13.  Show Sensor Status

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments