manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 349 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 349

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Run Mode

Chapter 6

page 327

How to Use Hot Keys

Descriptive labels

for Hot keys

CAMBIE

AL ESPANOL

USE THE CURSOR KEYS

ENABLE SENSORS

TO MAKE SELECTIONS.

COUNTERS

PRESS ENTER TO 

CAM SWITCH

ACCESS SELECTION.

BRAKE MONITOR
TONNAGE/WAVEFORM
PROCESS MONITOR
FEED CONTROL
PM MONITOR
TOOL INFORMATION
SHUTHGT/CNTRBAL
ERROR LOG
LOAD NEW TOOL
DIALOG MENU
TOGGLE HOT KEYS 1

270

VIEW SENSOR

SUMMARY

VIEW GLOBAL
CAM SUMMARY

ADJ SENSOR

PART EJECTION

ADJUST CAM
SPRAY LUBE

TONNAGE

PLAN VIEW

DISPLAY

SHUT HEIGHT

F1

F2

F3

F4

F5

F6

F7

F8

Use F1 - F8 as Hot keys

If you have the Bilingual Option,

F1 is reserved for changing

language and cannot be used

as a Hot key.

ADJUST

SETPOINTS

Figure 6 - 5.  Run Main Menu, Showing Hot Keys Programmed

In Run mode, Hot keys are function keys that are specially programmed to take you directly
to the screens you want. After you have programmed Hot keys, you can simply press the

F

 key next to the label describing the screen, and SmartPAC 2 goes to that screen.

Example

You frequently need to adjust the timing for the cam channel that controls part blowoff.  For
convenience, you set up a Hot key to take you directly to the cam channel’s adjust screen from
the main Run menu.

You can use all the function keys, 

F1 

through 

F8

 as Hot keys, unless you have the bilingual

option, which uses 

F1

 to change languages. You can recognize Hot keys in the main Run

screen by the red frame around their descriptive labels.  You can have two sets of Hot keys
(see next section), for a total of sixteen if you do not have the bilingual option.

NOTICE

If you add or remove an option, previously set Hot keys will not navigate correctly.  If this
happens, delete and re-program the Hot key or keys that are not working correctly.

Toggle Hot Keys

In the main Run menu, shown in the figure above, the last menu item says “TOGGLE HOT
KEYS 1.”  When this menu item shows, you can see the first set of Hot keys labels at the
right side of the display, if any are programmed.  To access the other set of Hot keys, use the
cursor keys to highlight “TOGGLE HOT KEYS 1.” “TOGGLE HOT KEYS 2” appears and
the second set of Hot keys labels also appears.  This menu item determines which set of Hot
keys you see.  For more information, see “TOGGLE HOT KEYS,” page 363.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments