manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 317 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 317

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Program Mode

Chapter 5

page 295

number of
strokes for
DiProPAC
to auto
enable ALL
sensors in
the tool

10

AUTO ENABLE COUNTER FOR THIS

STROKES

USE THE CURSOR KEYS TO CHANGE THE NUMBER
OF STROKES.  PRESS THE ENTER KEY WHEN
DONE.  PRESS THE RESET KEY TO CANCEL.

TOOL NUMBER 1234567
CHAIR BRACKET

TOOL IS

AUTO ENABLE COUNTER DETERMINES HOW MANY
STROKES THE SENSORS CAN BE DISABLED AT
A TIME.  THEY ARE AUTOMATICALLY ENABLED
AFTER REACHING THE COUNT.

Figure 5 - 20.  Setting "Auto enable by sensor" counter

2. After you have assigned a name for sensor 1 and set the auto enable counter value, you

will be returned to the previous menu where sensor 2 automatically is highlighted for
you.  You can select a name for it.  Continue in this manner until all your sensors have
been configured accordingly.

Setting Sensor Type

After selecting the sensor name, you will see this display. You can set sensor type.  Notice
that the sensor name now appears at the top right of the display. This display shows "Part
ejection.”

NOT USED

RED (NC)
YELLOW (NO)

GREEN
GREEN QUICK CHECK
GREEN CONSTANT
GREEN SPECIAL

USE CURSOR KEYS TO CHANGE SENSOR
TYPE.  PRESS ENTER TO SELECT.  PRESS
RESET WHEN DONE.

TOOL NUMBER 1234567
CHAIR BRACKET
CRITICAL ANGLE    0

SENSOR 1
PART EJECTION
GREEN  ESTOP

Figure 5 - 21.  Setting sensor type

Select the sensor type you want for that sensor. You have six choices: yellow, red, green,
green quick check, green constant, and green special. See Chapter 1 for a detailed description
of each of these sensors. (The "not used" setting is for sensor inputs that are not used with the
tool.)  Notice that the sensor function appears at the top middle of the display and the sensor
type at the top right.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments