manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 175 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 175

SmartPAC 2 with WPC Integration

1126800

Installing SmartPAC 2 and WPC

Chapter 2

page 153

One-hand Control Switch Tests (with Optional One-
hand Control)

DANGER

!

INJURY DURING TESTING

Keep all personnel away from the press during testing.

Ensure that there is no die or other tooling in the press during testing.

Failure to comply with these instructions will result in death or serious injury.

DANGER

!

MISSING SAFEGUARDS

Install a light curtain for use with the one-hand control option.  A light curtain is required for
using the one-hand control.

Failure to comply with these instructions will result in death or serious injury.

WARNING

!

ELECTRIC SHOCK HAZARD WHEN WORKING INSIDE ENCLOSURE WITH POWER ON

•

DO NOT touch electrical connections or circuit boards.

•

Ensure that this test is performed by qualified personnel.

Failure to comply with these instructions could result in death or serious injury.

NOTICE

Refer to the WPC LED map, Figure B at the end of the manual.

NOTICE

Depress the One-hand Control Switch quickly and fully to initiate a stroke.  If you depress
the One-hand Control Switch slowly or partially, a stroke will not be initiated.

NOTICE

If the Interrupted Stroke message is flashing on the display, WPC has automatically changed
to Two-hand Maintained mode. You must depress and hold the run buttons to complete the
stroke and clear the Interrupted Stroke. (see “Interrupted Stroke,” page 364).  One-hand
Control will not work while the Interrupted Stroke message is on.

Perform these tests if your WPC is equipped with a One-hand Control Switch.   

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments