manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 513 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 513

REVISIONS

REV

DESCRIPTION

DATE

APP’D

B

WPC LOCKOUT RELAY

MOTOR STOP

MOTOR START

FORWARD OVERLOAD

REVERSE OVERLOAD

M F

M R

M F

M R

L1 120 VAC

L2 NEUTRAL

STOP/ START MOTOR CONTROL STATION

WIRING WITH LOCKOUT

ADB

+ 24 VDC FROM WPC #9

WPC #135

To WPC #7  (Motor forward input)

To WPC #17 (Motor reverse input)

MF

MR

MOTOR FORWARD COIL

MOTOR REVERSE COIL

WPC #137

Forward

Reverse

FIGURE 7

SENSING AND CONTROL

CODE IDENT NO.

DRAWING NUMBER

APPROVALS

HONEYWELL

FILENAME

DRAWN

TITLE

SHEET

SCALE

DATE

CHK.

ENG.

MFG.

SIZE

REV

REL

OF

any part thereof, any information contained therein or any physical article or    

thereof confers or transfers any right to reproduce or disclose the document,  

device, or to practice any method or process, except by written permission or

PROPRIETARY RIGHTS.  This document discloses subject matter in which
HONEYWELL has proprietary rights.  Neither receipt nor possession 

written agreement with HONEYWELL.

12/7/01

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments