manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 292 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 292

1126800 

SmartPAC 2 with WPC Integration

Page 270

Chapter 4

SmartPAC 2 Initialization Mode

Press Speed Compensation for Link Motion

NOTICE

Perform press speed compensation procedure for each tool if Settling Time is not an
initialization parameter for this SFI.

If SETTLING TIME is 

not

 on the list of Initialization parameters, use this method of

compensation.  If you use Press Speed Compensation, you must follow these steps for every
tool the first time you program it.

1. Go to Program mode.

2. Select PROGRAM OR LOAD TOOL NUMBER.  Select the tool in the press.

3. Select FEED CONTROL, select FEED ADVISOR.  Select PRESS SPEED and enter a

value 10% greater than the actual press speed. Select CALCULATE.

4. Load the tool number in SmartPAC 2 for the tool that is in the press. Cycle the press and

notice whether feeding is complete at the correct time, or too soon or too late.

•

If feeding is complete at the correct time, you are finished with Link Motion
compensation.

•

If feeding is completed too late, go to Program Mode and increase the Press Speed in
the Feed Advisor by 3% and select CALCULATE again. Load the tool number.  Run
the press and observe the feeding again.  Continue to increase Press Speed in the Feed
Advisor by 3% increments until feeding is complete at the correct time.

•

If feeding is completed too soon, decease the Press Speed in the Feed Advisor by 3%
and select CALCULATE again. Load the tool number.  Run the press and observe the
feeding again.  Continue to decrease Press Speed in the Feed Advisor by 3%
increments until feeding is complete at the correct time.

Using a Computer Keyboard to Enter Names

For convenience when entering alphabetic, numeric and symbol characters, you can use a
computer keyboard connected to SmartPAC 2, as follows.

1.

 

Power down SmartPAC 2.

2.

 

Plug the keyboard into the appropriate connector on the SmartPAC 2 board (see
Figure 2 - 39, page 162).

•

Keyboard with a USB connector:

  Plug into the USB connector.

•

Keyboard with a PS/2 connector:

  Plug the keyboard into the PS/2 connector.

3.

 

Power up SmartPAC 2.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments