Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 208

Page: 208 / 230

Appendix A - Installing RTP

a. Remove the relevant key tabs from the terminal block to allow connection

with the module.

b. Connect the appropriate cable to the module at ControlEdge 900

Controller. Possible options are:

900RTC-H210 Remote Termination High Voltage Cable Assembly, 1.0
meters long

900RTC-H225 Remote Termination High Voltage Cable Assembly, 2.5
meters long

900RTC-H250 Remote Termination High Voltage Cable Assembly, 5.0
meters long

c. Install the module label onto the module connector cover.

d. Connect shield drain wire to the grounding bars at the base of the

ControlEdge 900 Controller rack. All field-wiring shields must be grounded
as described in the shield grounding section.

2. Mount the RTP to the DIN rail.

a. Secure the RTP to the rail. See "Securing the RTP to the DIN rail" on

page 228 for more information. for details.

b. Connect the cable to the RTP.

208

Summary of Contents for ControlEdge 900 platform







































































































































































































































Search results

Summary of Contents for ControlEdge 900 platform

Reviews:

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 208 / 230

Search results

Summary of Contents for ControlEdge 900 platform

Reviews: