Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 177

Page: 177 / 230

177

Item LED

LED
State/Color

Description

Module
Status

Solid Green

Power on with self-test passed

Solid Red

In power-up process or hardware failure or firmware
corrupt

Blink Green
(@ 4 Hz)

Normal scanning

Blink Red
(@ 0.5 Hz)

Firmware upgrade

Blink Red
(@ 1
strobe)

Communication error

Blink Red
(@ 3
strobe)

Running with error for module diagnostic and
channel diagnostics (detected by the module itself)

Channel
LEDs

Digital Input:

OFF

Channel disabled or State 0

On/Green

State 1

Digital Output

OFF

Channel disabled or State 0

On/Green

State 1

Analog Input

OFF

Analog Output

OFF

Chapter 8 - Diagnostics and Troubleshooting

Summary of Contents for ControlEdge 900 platform







































































































































































































































Search results

Summary of Contents for ControlEdge 900 platform

Reviews:

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 177 / 230

Search results

Summary of Contents for ControlEdge 900 platform

Reviews: