Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 112

Page: 112 / 230

Item

Description

Short Circuit Current

24.5 mA +/- 0.5 mA

Open Wire Current

<1mA

Input Impedance

Typically 250 ohm

A-D conversion

16 bit

Accuracy

0.1% of full scale (23.5 ± 2°C)

0.17% of full scale (-0 to 60°C)

Input filter

First-order low-pass 100Hz

The following items are not directly supported by UIO AIs:

Voltage inputs (1-5 or mv)

Thermocouples

RTDs

NAMUR devices

Devices that supply current, which is not first supplied by the
external 24V to the device. For example, a device that creates
current (even if referenced to Honeywell ground).

Standard 2-wire transmitter with UIO

Figure 5-23: Standard 2-wire transmitter with UIO (Loop Powered)

112

Summary of Contents for ControlEdge 900 platform







































































































































































































































Search results

Summary of Contents for ControlEdge 900 platform

Reviews:

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 112 / 230

Search results

Summary of Contents for ControlEdge 900 platform

Reviews: