Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 19

Page: 19 / 230

Table 3-2: System component list for ControlEdge 900 PLC Hardware

Item

Component
Name

Description

Source

I/O Rack

System may consist of 5 different types of
I/O racks:

4-slot w/1 power supply

8-slot w/1 power supply

12-slot w/1 power supply

8-slot w/redundant power supplies

12-slot w/ redundant power upplies

Local I/O Rack

1 I/O Rack

1 CPM (for controller racks) or 1 EPM
(for I/O racks)

Up to 4, 8 or 12 I/O modules

1 or 2 Power Supplies
Optional second Power Supply and
Power Status Module (PSM) on 8-
and 12-slot I/O rack.
A Power Status Module (PSM) is
required with redundant power
supplies.

Redundant CPM
Rack

1 Redundant Controller Rack

2 Power Supplies

2 CPMs: Redundancy is provided by
two CPMs operating in a Redundant
Controller Rack; this rack has no I/O
modules.

1 Filler block cover

Honeywell

Expansion I/O
Rack (Optional)

Includes:

1 rack

1 Power Supply

Optional second Power Supply and

Honeywell

Summary of Contents for ControlEdge 900 platform







































































































































































































































Search results

Summary of Contents for ControlEdge 900 platform

Reviews:

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 19 / 230

Search results

Summary of Contents for ControlEdge 900 platform

Reviews: