Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 51

Page: 51 / 230

9. Use the Firmware Manager to laod firmware to the new CPM to

match the version that is running in the primary redundant
partner CPM.

10. Check the redundancy synchronization state by monitoring the

role LED of the primary or secondary CPM.

To replace an unsynchronized primary CPM,:

Refer to Replacing a non-redundant UOC-CPM section for this
information.

Following section provides information about replacing EPM, I/O
Module and Spare parts that are common to both PLC and UOC.

Table 4-3: Reference for replacing EPM, I/O Module and Spare parts that are common
to both PLC and UOC

Component
replacement

Reference

EPM

For information about replacing EPM, see the section

EPM

device replacement

I/O Module

For information about replacing I/O Module, see the section

I/O

module replacement

Spare parts

For information about replacing spare parts, see the section

Spare parts

Summary of Contents for ControlEdge 900 platform







































































































































































































































Search results

Summary of Contents for ControlEdge 900 platform

Reviews:

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 51 / 230

Search results

Summary of Contents for ControlEdge 900 platform

Reviews: