manualshive.com logo in svg

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 110 / 230

Share
Download
Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 110

In above diagram, each power supply source supplies power to the
whole module. If redundant power supply are provided, the UIO
module still can work in case of failure on one power source.

At least one power supply is required, otherwise UIO module cannot
work and "External power" error is reported.

ATTENTION:
Calibrate the power output at 24 V DC to limit the PWB thermal
rise.

See the following table for the UIO specification of different hardware
versions:

Table 5-14: UIO specification of different hardware versions

Item

Hardware Version B

Hardware Version
D/E

ControlEdge Builder
Display*

Version 01.00

Version 02.00

AO Channel Specs
without DO channels
used

Maximum of 5 into 100 ohms with no
other channels configured

No load
restrictions:

110

Summary of Contents for ControlEdge 900 platform







































































































































































































































Reviews:

No comments