manualshive.com logo in svg

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 54 / 230

Share
Download
Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 54

n

8-slot or 12-slot I/O rack with non-redundant power supply

n

8-slot or 12-slot I/O rack with redundant power supply

A Power Status Module is required if the I/O rack with redundant
power supply is used.

Figure 5-1: Rack Options

Additionally, to eliminate single point of failure, you can also use the
dual rack redundancy solution.

As part of this solution you have two single slot racks deployed
separately in different areas. The distance between the two racks can
be 100 meters if you use a Cat6 shielded cable. Each one slot rack
hosts a power supply, a controller module, and a redundancy module
(ReduModule (RM) is being introduced as part of the dual
rack redundancy solution). Another one slot rack with the same
modules is deployed at a different location. The connection between
the two racks is established using a specific Ethernet LAN cable.
Ethernet ports are present in both the Redundancy Modules (RM).

54

Summary of Contents for ControlEdge 900 platform







































































































































































































































Reviews:

No comments