Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 11

Page: 11 / 230

Terminology Description

HMI

Human Machine Interface

HSR

High Availability Seamless Redundancy

I/O Rack

ControlEdge 900 form factor rack with 4, 8, or, 12 I/O slots and one
slot for non-redundant CPM or EPM.

PLC

Programmable Logic Controller

PSM

Power Status Module

PSU

Power Supply Unit

PWA

Printed Wiring Assembly

Redundant
Controller
Rack

ControlEdge 900 rack capable of hosting a redundant pair of CPMs.

Redundancy Module

RTP

Remote Termination Panel

RIUP

Removal and Insertion Under Power

SCADA

Supervisory Control and Data Acquisition

UIO/UIOM

Universal Input/ Output (Module)

UOC

Unit Operations Controller (Experion). This is a term used to refer to
the CPM when used as a controller in the Experion PKS Distributed
Control System.

Chapter 1 - About this guide

Summary of Contents for ControlEdge 900 platform







































































































































































































































Search results

Summary of Contents for ControlEdge 900 platform

Reviews:

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 11 / 230

Search results

Summary of Contents for ControlEdge 900 platform

Reviews: