Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 99

Page: 99 / 230

Update Rate: 6 ms Maximum

Switching current: 2.6mA norminal

Galvanic Isolation: Between Field wiring (input or output) and
Module

Power supply Loading:

5 V; 130 mA maximum

24v; 40 mA maximum

Digital Output Module (8 Channels) - AC Voltage
Type

DO AC Voltage type module supports:

Channel Density: 8 Channels

Output Type: Triac (Zero switching voltage)

Input voltage range: 85 V AC to 240 V AC.

Isolation: Galvanic ally isolated per Channel to channel and
channel to rack.

Transient Overload Voltage Protection

Maximum Load Current: 2 A per channel and 8 A max. per module
(Resistive load)

OFF to ON Response Time*: 3 ms + 0.5 line cycle max

ON to OFF Response Time*: 3 ms + 0.5 line cycle max

Power Supply Loading: 5 V: 220 mA max and 24V: 0 mA

Per channel Field-replaceable fuse support

20 pin EURO style terminal block

RTP support. For more information, see Using an RTP to field
wiring the 8 Point AC DO section.

TIP:
*Excluding controllers scan time and excluding transmission
time from module to rack.

Digital Output Module (32 Channels) - DC Voltage
Type

The Digital Output Module – DC Voltage Type is current sourcing type
module.

DO DC Voltage type module supports:

Summary of Contents for ControlEdge 900 platform







































































































































































































































Search results

Summary of Contents for ControlEdge 900 platform

Reviews:

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 99 / 230

Search results

Summary of Contents for ControlEdge 900 platform

Reviews: