Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 65

Page: 65 / 230

Table 5-3: Installation tools

Types

Item

Description

Common
tools

Wire strippers

For Power Supply and for I/O
Wiring

Crimper

For Terminal Lugs on Power
Supply wiring and on I/O wiring
shields

Screwdrivers Small flat-tip

For Euro-style Terminal Blocks

Small/medium flat-tip or #2
Phillips or 3/16 inch slotted
screwdriver

For Barrier style Terminal blocks;
also for captured screws in
Terminal Blocks

Large (long blade)

For use as I/O Module extractor

Other

Electric drill, with drill bits for
#10 or M4 screws, and with drill-
bit extender

For rack mounting

Vacuum cleaner, brush

For use during and after drilling
operations

Pen, ball-point or felt-tip, for
entering data on labels for I/O
modules)

For entering data on labels for I/O
modules

Multi-Meter (Volt/Ohms/Amps)

For safety checks and for
equipment test

Soldering pencil or gun (for
attaching filter capacitors to I/O
wiring shields)

For attaching filter capacitors on
I/O wiring shields

Preparing the installation site

Table 5-4: Site and equipment preparation

Step Procedure

For more
information, see

Racks (4-, 8- and 12-slot)

Mount racks

section.

Install (or verify correct installation of) enclosures for
CPM and ancillary equipment:

Mount racks

section

Installing I/O

Summary of Contents for ControlEdge 900 platform







































































































































































































































Search results

Summary of Contents for ControlEdge 900 platform

Reviews:

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 65 / 230

Search results

Summary of Contents for ControlEdge 900 platform

Reviews: