Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 16

Page: 16 / 230

Modbus TCP Slave

OPC UA Server

HART IP

ControlEdge Builder Controller Configuration protocol

Privacy protocol

SNTP (if NTP server is enabled)

Destination DHCP for uplink

Modbus Master and OPC UA Client that configured in the relative
function blocks

CDA Responder

The port number can be configured in ControlEdge Builder, and see
the following table for the default port numbers.

Table 3-1: Default port numbers

Port number Port number type

Description

41103

Fixed destination port

Builder protocol

24558

Fixed destination port

Discovery protocol

9050

Fixed source port

Discovery protocol

123

Fixed source port

SNTP protocol

123

Fixed destination port

SNTP protocol

Fixed destination port

DHCP Client for uplink

500

Fixed destination/source port

IPSec for uplink (IKE ports)

4500

Fixed source port

IPSec for uplink(IKE ports)

55601

Fixed destination port

IPSec for uplink(CertMngr cleartext)

55602

Fixed destination port

IPSec for uplink(CertMngr encryption)

Fixed source port

IPSec for uplink (SCEP)

Summary of Contents for ControlEdge 900 platform







































































































































































































































Search results

Summary of Contents for ControlEdge 900 platform

Reviews:

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 16 / 230

Search results

Summary of Contents for ControlEdge 900 platform

Reviews: