Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 26

Page: 26 / 230

Table 3-5: LED Indications on PLC-CPM

Item LED

LED
State/Color

Description

Status

OFF

No Power is applied to CPM.

On/Green

The controller is working normally.

On/Red

The controller is stopped.

On/Orange

The controller is in power-up process.

Blinking Red
@ 1HZ

The controller is running with error.

Blinking Red
@ 0.5HZ

The controller is accessible via online
communication, but no application is
loaded.

Blinking Red
@ 5HZ

IP address is in conflict.

Blink @ 1HZ /
Green &
Orange

The controller is upgrading firmware.

Role

OFF

It is a non-redundant system or;

On/Green

The controller is in primary role and the
system is synchronized, or;

On/Orange

The controller is in secondary role and
the system is synchronized.

Blinking
Green @ 1HZ

The controller is in primary role and the
system is synchronizing.

Blinking
Orange @
1HZ

The controller is in secondary role and
the system is synchronizing.

Blinking
Green @
0.5HZ

The controller is in primary role and the
system is unsynchronized.

Blink Red @
0.5HZ

The controller is in secondary role and
the system is unsynchronized.

3, 5,
7, 9

Ethernet Port
Speed ( Upper
LED)

Yellow On/Off

OFF for 10Base-T; ON for 100Base-TX.

Summary of Contents for ControlEdge 900 platform







































































































































































































































Search results

Summary of Contents for ControlEdge 900 platform

Reviews:

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 26 / 230

Search results

Summary of Contents for ControlEdge 900 platform

Reviews: