Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 142 | Manualshive

Page: 142 / 230

Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 142

CAUTION:

Hazardous voltages

exist at terminal blocks.

Using switches at field devices disconnect the field wiring form
power sources before servicing.
Failure to comply with these instructions could result in death or
serious injury.

If installing 8 channel Analog Output module, set its DIP switch as
follows. (Switch is located at edge of module, marked “SW1”.)

n

For internal rack power, set DIP switch to ON.

n

For external power (18-36V), set DIP switch to OFF (default).

NOTE: 24VDC external power is required if using 6 or more 8-pt.
AO modules or 3 or more 16-pt. AO modules.

A small slotted screwdriver or paperclip works well; avoid using
pencils.

Figure 5-54: Dip Swith Position of 8 Channel AO

Figure 5-55: 8 Channel Analog Output Wiring Diagram

142

«
...
140
141
142
143
144
...
»

Summary of Contents for ControlEdge 900 platform







































































































































































































































Reviews:

No comments