manualshive.com logo in svg

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 28 / 230

Share
Download
Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 28

current configuration is available.

n

It is recommended to bring the process to a safe and orderly
shutdown.

You will need a #2 Phillips screwdriver.

To replace a non-redundant or unsynchronized primary PLC-CPM

1. If a process is currently in operation, bring it to the safe mode, and

orderly shutdown if it is required.

2. Using an external (user-supplied) switch, disconnect the power

supply in the rack (associated with the CPM to be replaced) from
the source main power.

3. Observe where communications cables are plugged into the CPM,

and if necessary, tag them to identify their functions. Unplug all
communications cables.

4. At the top and bottom of the module, loosen the captured screws

that secure the module in the rack, and remove the CPM from the
rack. (Note that an up/down rocking motion helps with removal of
the module.)

5. Ensure that the new CPM is properly aligned with the slot guides,

insert the new CPM in the rack, and secure it in place with the
captured screws at top and bottom of the module.

6. Re-install communications cables.
7. Set the new CPM’s mode switch position to STOP (to prevent an

old/stale configuration from running and to enable firmware
update and configuration load).

8. Using the (user-supplied) switch, re-connect power supply in the

rack (associated with the new CPM) the source main power to the
rack.

9. Optional-for IPsec enable system, if Secure Communication is

enabled in the system, disable the IPsec in the PC installed the
ControlEdge Builder. See "Disable IPsec policy on PCs" in

ControlEdge PLC and ControlEdge RTU Network and Security
Guide

for more information.

10. Use the ControlEdge Builder to load firmware to the new CPM to

match the version that was running in the removed CPM.

11. Use the ControlEdge Builder to download the configuration to the

new CPM.

12. Set the new CPM’s mode switch position to the desired operation

state.

13. Optional-for IPsec enable system, setup certificates and IPsec

policy in the CPM. See "Setup certificates and IPsec policy in

28

Summary of Contents for ControlEdge 900 platform







































































































































































































































Reviews:

No comments