Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 228

Page: 228 / 230

Appendix A - Installing RTP

Securing the RTP to the DIN rail

1. Secure mounting screws at each end of the mounting rail with additional

screws approx. every 8"(203mm) to prevent the rail from twisting.

2. Insert one side of the DIN rail at position A, as shown below.

3. Insert the other side of DIN rail at position B, and push gently to snap the DIN

rail.

4. To remove the DIN rail, use a slot screwdriver to lift the clip at position C

gently (the plastic is fragile) to disengage the DIN rail at position B. Lift the
plastic clip up and over the rail, then disengage at position A.

228

Summary of Contents for ControlEdge 900 platform







































































































































































































































Search results

Summary of Contents for ControlEdge 900 platform

Reviews:

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 228 / 230

Search results

Summary of Contents for ControlEdge 900 platform

Reviews: