Hitachi L300P-1100H Instruction Manual Download Page 80

Page: 80 / 130

4-40

Start frequency

This frequency is the value the operator must set before the Inverter will give

an output.

Mainly used when an operator adjusts the start torque.

By setting the start frequency higher, direct starting is caused and the starting current increases. Therefore an

overload is within the restriction range and the inverter has a tendency to trip on over-current protection.

Function

code

Set range

Description

b082

0.10 to 9.99

Units : Hz

Reduced voltage start selection

This function is to raise the voltage slowly on motor starting.

The lower this value the more torque is available on starting.

However, by making this value lower, the inverter has a tendency of tripping on

over-current protection, because of almost direct starting.

Function

code

Data

Time to take for reduced
voltage starting

No reduced voltage start

b036

Short (about 6ms)

Long (about 36ms)

Chapter 4 Explanation of function

b082:Start frequency

Relation code

b036:Reduced voltage

start selection

b082:Start frequency

Relation code

Output frequency

Output voltage

b082

b036

Output frequency

Output voltage

Starting frequency

b082

---

Summary of Contents for L300P-1100H



































































































































Search results

Summary of Contents for L300P-1100H

Reviews:

Related manuals for L300P-1100H

Brands by name

Popular brands

Hitachi L300P-1100H, Instruction Manual

Search results

Summary of Contents for L300P-1100H

Reviews:

Related manuals for L300P-1100H

Brands by name

Popular brands