Hitachi L300P-1100H Instruction Manual Download Page 53

Page: 53 / 130

4-13

Accumulated time monitor on RUN

The operation time of inverter is accumulated and the value is displayed.

(Display)

0. - 9999. : Display is in 1 hour units.

1000 - 9999

: Display is in 10 hour units.

100 - 999

: Display is in 1000 hour units.

Power ON time monitor

This accumulates the time running to the inverter and displays the value.

(Display)

0. - 9999. : Display is in 1 hour units.

1000 - 9999

: Display is in 10 hour units.

100 - 999

: Display is in 1000 hour units.

Trip time monitor

This displays the number of inverter trips.

(Display)

0. - 9999. : Display is in 1 times unit.

1000 - 6553 : Display is in 10 times unit.

Trip monitor 1-6

This displays the details for the last six protective trips.

The trip monitor 1 displayed the details of the last trip.

(Display contents)

[1] Trip Code (Display anything from E01 to E79.)(Note 1)

[2] Output frequency on tripping (Hz)

[3] Output current on tripping (A)

[4] The direct voltage (between P and N) on tripping (V)

[5] The accumulated time inverter was operating until tripping (h)

[6] The accumulated time inverter was run until tripping (h)

(Note 1) Please refer to the pages 4.4 Protection function list (2) Trip monitor display.

Chapter 4 Explanation of function

d016: Accumulated time

monitor on RUN

Relation code

d017: Power ON time

monitor

Relation code

d080: Trip time monitor

Relation code

d081: Trip monitor 1

d082: Trip monitor 2

d083: Trip monitor 3

d084: Trip monitor 4

d085: Trip monitor 5

d086: Trip monitor 6

The methods of trip monitor

Relation code

(Note 2) In case of no tripping

is displayed.

(1) Trip factor

(Note 2)

(2) Trip frequency

(3) Trip current

(4)Trip voltage
(P-N)

(5) Accumulated

(6) Power ON

機能

FUNC

機能

FUNC

Summary of Contents for L300P-1100H



































































































































Search results

Summary of Contents for L300P-1100H

Reviews:

Related manuals for L300P-1100H

Brands by name

Popular brands

Hitachi L300P-1100H, Instruction Manual

Search results

Summary of Contents for L300P-1100H

Reviews:

Related manuals for L300P-1100H

Brands by name

Popular brands