Hitachi L300P-1100H Instruction Manual Download Page 95

Page: 95 / 130

4-55

RUN time / power ON time over (RNT/ONT)

When the accumulated operation time reaches or is over the

Setting time in b034, RUN time/power ON time over (RNT/ONT)

output is switched.

Function

code

Data

Description

b034

1. -9999.

1000-6553

Don’t operate.

Set by 10-hour unit.

Set by 100 hours unit. (10000-65530 hours)

(1) Run time over (RNT)

Assign 11(RNT) to an intelligent output terminal 11, 12 (C021, C022) or the alarm relay output terminal

(C026).

Set ON time level with b034.

(2) Power ON time over (ONT)

Assign 12(ONT) to an intelligent output terminal 11, 12 (C021, C022) or the alarm output terminal, (C026).

Set ON time level with b034.

Force operation ope function

This function is used to operate from the operator forcibly by on/off

of an intelligent terminal when frequency and operation command

is selected other than the operator.

Becoming the operation from the frequency and operation command that was selected by A001 and A002 if

the signal is off, and becoming the frequency and operation command from an operator forcibly if the signal is

on when the compulsion operation function is selected by an intelligent input selection.

When changed the operation command while driving, operation command is canceled and become stoppage

at first.

Operation command from each command input the operation command once again as the stoppage at first for

driving once again.

Setting item

Function cord

Setting value

Contents

Frequency command selection

A001

Potentiometer the digital operator has

Terminal

Operator

RS485

Option 1

Option 2

Operation command selection

A002

Terminal

Operator

RS485

Option 1

Option 2

Intelligent input selection

C001-C005

OPE : Compulsion operation

Relation code

Chapter 4 Explanation of function

b034 : Warning time level

C021,C022: Intelligent output terminal

C026 : Alarm relay output terminal

d016 :Accumulation time monitor during RUN

d017 :Power ON time monitor

Relation code

A001: Frequency setting selection

A002: Operation command selection

C001-C005: Intelligent input terminal

Relation code

Summary of Contents for L300P-1100H



































































































































Search results

Summary of Contents for L300P-1100H

Reviews:

Related manuals for L300P-1100H

Brands by name

Popular brands

Hitachi L300P-1100H, Instruction Manual

Search results

Summary of Contents for L300P-1100H

Reviews:

Related manuals for L300P-1100H

Brands by name

Popular brands