Hitachi L300P-1100H Instruction Manual Download Page 20

Page: 20 / 130

2-2

2.1.1 Installation

1. Transportation

This inverter has plastic parts. So handle with care.

Do not over tighten the wall mounting fixings as the mountings may crack, causing is a risk of falling.

Do not install or operate the inverter if there appears to be damage or parts missing.

2. Surface for Mounting of Inverter

The temperature of the Inverter heatsink can become very high (the highest being about 150ºC). The

surface, which you are mounting the Inverter onto, must be made of a non-flammable material (i.e. steel)

due to the possible risk of fire. Attention should also be made to the air gap surrounding the Inverter.

Especially when there is a heat source such as a breaking resistor or a reactor.

3. Operating Environment - Ambient Temperature

The ambient temperature surrounding the Inverter should not exceed the allowable temperature range

(-10 to 40ºC). When using at 50ºC of ambient air temperature, the rated output current will be reduced.

(P.4-18)

The temperature should be measured in the air gap surrounding the Inverter, shown in the diagram

above. If the temperature exceeds the allowable temperature, the component life will become shortened

especially in the case of the Capacitors.

4.Operating Environment - Humidity

The humidity surrounding the Inverter should be within the limit of the allowable percentage range (20%

to 90%). Under no circumstances should the Inverter be in an environment where there is the possibility of

moisture entering the Inverter.

Also avoid having the Inverter mounted in a place that is exposed to the direct sunlight.

Chapter 2 Installation and Wiring

Keep the space enough not to be

prevented the ventilation of cooling by up

and down of wiring duct.

5cm or more

(Note 1)

(Note 2)

Inverter

Flow of the air

Wall

(Note 1) 10cm or more for 11 to 75kW

30cm or more for 90 to 132kW

(Note 2) 10cm or more for 11 to 75kW

30cm or more for 90 to 132kW

But for exchanging the DC bus

capacitor , take a distance.

10cm or more for 11 to 15kW

22cm or more for 18.5 to 75kW

30cm or more for 90 to 132kW

Summary of Contents for L300P-1100H



































































































































Search results

Summary of Contents for L300P-1100H

Reviews:

Related manuals for L300P-1100H

Brands by name

Popular brands

Hitachi L300P-1100H, Instruction Manual

Search results

Summary of Contents for L300P-1100H

Reviews:

Related manuals for L300P-1100H

Brands by name

Popular brands