Hitachi L300P-1100H Instruction Manual Download Page 85

Page: 85 / 130

4-45

Second control function(SET)

This control function is used when the Inverter is connected to two different types of motors. By assigning

08(SET) to an intelligent input terminal and turning SET terminal ON/OFF you can switch between two different

Inverter set-ups.

Select 2

control function while the Inverter is in the STOP condition.

The functions which can change with SET terminal

F002/F202 : 1

/ 2

acceleration time

F003/F203:1

/ 2

deceleration time

A003/A203:1

/ 2

base frequency

A004/A204:1

/ 2

max. frequency

A20/A220:1

/ 2

multi-speed 0 setting

A041/A241:1

/ 2

torque boost selection

A042/A242:1

/ 2

manual torque boost

A043/A243:1

/ 2

manual torque boost point

A044/A244:1

/ 2

control system

A061/A261:1

/ 2

frequency maxmum limiter

A062/A262:1

/ 2

frequency minimum limiter

A092/A292:1

/ 2

acceleration time 2

A093/A293:1

/ 2

deceleration time 2

A094/A294:1

/ 2

two-stage adjustable speed selection

A095/A295:1

/ 2

two-stage acceleration frequency

A096/A296:1

/ 2

two-stage deceleration frequency

b012/b212:1

/ 2

electronic thermal level

b013/b213:1

/ 2

electronic thermal characteristic selection

H003/H203:1

/ 2

allowable motor selection

H004/H204:1

/ 2

allowable motor pole selection

H006/H206:1

/ 2

stabilized constant

Display during setting isn’t differentiated between the 1

control function or the 2

control function. So confirm

it in the state of ON/OFF of termnal.

Even if 1

/ 2

control is changed during run, it will not be active until the inverter is stopped.

Software lock mode selection(SFT)

This function is used to prevent changing data by mistake.

When you want to use an intellignent input terminal, assign 15(SFT).

Below is the software lock code selection.

Function code

Data

SFT

terminal

Description

ON/OFF

Write disable except for b031/write enable

ON/OFF

Write disable except for b031,F001,A020,A220,

A021~A035,A038 / write enable

Write disable except for b031

Write disable except for b031,F001,A020,A220,

A021~A035,A038

b031

Write disable except for change mode during running (code
list reference)

Chapter 4 Explanation of function

Motor1

Motor2

Inverter

SET

CM1

b031 :Software lock mode selection

C001-C005: Intelligent input setting

Relation code

Summary of Contents for L300P-1100H



































































































































Search results

Summary of Contents for L300P-1100H

Reviews:

Related manuals for L300P-1100H

Brands by name

Popular brands

Hitachi L300P-1100H, Instruction Manual

Search results

Summary of Contents for L300P-1100H

Reviews:

Related manuals for L300P-1100H

Brands by name

Popular brands