manualshive.com logo in svg

Hioki DM7275 Series, Instruction Manual

Share
Download
Hioki DM7275 Series Instruction Manual Download Page 89

86

Statistical Calculations

The statistical calculation results are automatically cleared at the following times:

 • When the user clears the statistical calculation results

 • When the user clears the statistical calculation results

See “If you do not wish to clear the statistical calculation results every time they are printed” (p. 86)

 • When the user changes the measurement conditions (temperature compensation, scaling, NULL)

 • When the user changes the comparator settings (p. 53)

 • When the user changes the BIN settings (p. 57)

 • When the instrument is reset (p. 93)

 • When measurement conditions are loaded using the panel load function

 • When the instrument is turned off (p. 28)

Printing

Touching 

PRINT

 prints the statistical calculation results. 

If there is no valid data, only the number of data points will be printed. If there is one valid data 

point, the sample standard deviation and process capability index will not be printed.

If you do not wish to clear the statistical calculation results every time they are 

printed

(Measurement screen) 

MENU

 > 

I/F

1

 

2

 

3

 

ON

Automatically clears the statistical 

calculation results every time they 

are printed.

OFF

Does not clear the statistical 

calculation results.

(Default setting)

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DM7275 Series
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands