manualshive.com logo in svg

Hioki DM7275 Series, Instruction Manual

Share
Download
Hioki DM7275 Series Instruction Manual Download Page 162

162

Functional Specifications

Measured value format

Operation

Changes the format of responses to measured value queries. 

RANGE FIX setting: Exponential part fixed based on the 

measurement range

FLOAT setting: Floating point

(When using the FLOAT setting, the instrument automatically 

transitions to the STOP state when transitioning to the 

REMOTE state.)

Setting

Measured value format: RANGE FIX, FLOAT

Default setting

Measured value format: RANGE FIX

SCPI ID

Operation

Sets the response string for the 

*IDN?

 query.

Setting

SCPI ID: Up to 127 characters

Default setting

Blank (HIOKI, model name, serial number, software version)

Remote

When communicating with the LAN, USB, RS-232C, or GP-IB interface, places the 

instrument in the remote state and disables touch panel and key operations. 

The

 [TRIG] 

key functions except while the instrument is in the RUN state.

The remote state can be canceled as follows:

 •By pressing the 

LOCAL

 key on the touch panel

 •By cycling the instrument’s power

 •By sending the :

SYSTem:LOCal

 command with the LAN, USB, RS-232C, or GP-IB 

interface

 •By sending the 

GTL

 command with the GP-IB interface

Startup settings

Operation

Selects which settings to apply when the instrument is turned 

on. 

Settings

Startup setting: LAST, FACTORY, PANEL

Panel: No. 01 to No. 30

Default settings

Startup setting: LAST

Panel: No. 01

Reset

Reset

Reverts all settings other than panel data and interface 

settings to their factory defaults. 

(Operation is the same as for the 

*RST

,

 :SYSTem:PRESet

,

 

 

:STATus:PRESet

 commands.)

System reset

Reverts all settings to their factory defaults. 

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DM7275 Series
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands