manualshive.com logo in svg

Hioki DM7275 Series, Instruction Manual

Share
Download
Hioki DM7275 Series Instruction Manual Download Page 24

18

Operating the Instrument

Switching the measured value display

 

Operation key

Each time the key is pressed, the measured 

values shown on the screen will switch between 

voltage only and voltage and temperature.

Touch panel

1

2

 •When measuring temperature, connect the temperature sensor to the instrument in advance. 

(p. 27)

 •Temperature measured values are not shown on the trend display or settings screens.

 •The instrument will continue to measure temperature internally even if the temperature is not 

being displayed on the screen.

 •The temperature display is updated together with the voltage display.

Changing the range

See “3.2 Setting the Measurement Range” (p. 35).

Operation keys

Causes the optimal range to be set automatically.

(Auto-range operation)

Switches the range.

Touch panel

1

2

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DM7275 Series
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands