manualshive.com logo in svg

Hioki DM7275 Series, Instruction Manual

Share
Download
Hioki DM7275 Series Instruction Manual Download Page 20

14

Part Names and Functions

1.3  Part Names and Functions

Front

1

2

3

4

5

1

Display

 

(Touch panel)

View measured values, settings, and judgment results; configure instrument settings.

 •Display the Settings screen and Measurement screen (measured values and judgment 

results) (p. 16).

 •Configure settings (p. 17).

2 Operation 

keys

For more information: See 

“1.5 Operating the Instrument” (p. 17)

.

[V/°C]

 key

Toggles display of 

temperature measured 

values. 

[AUTO]

 key

Enables auto-range 

operation (to automatically 

select an appropriate range).

[NULL]

 key

Adjusts the instrument’s 

zero-point.

[RANGE]

 

[

]

 key

Increases the range (to 

measure high voltages).

[RUN/STOP]

 

key

Starts and stops 

measurement.

[

]

 key

Decreases the range (to 

measure at a higher degree 

of resolution).

[TRIG]

 key

Starts measurement (to 

make measurements at 

the desired timing).

[SPEED]

 key

Changes the measurement 

speed.

3 POWER 

button 

(p. 28)

Switches the instrument’s 

power state.

OFF:

The instrument is off (no power is being supplied).

RED:

The instrument is in the SLEEP state (power is 

being supplied).

GREEN: The instrument is on. 

4 USB flash drive 

connector

Outputs measurement data, screen data, and measurement conditions; loads 

measurement conditions 

(p. 115)

.

5

Voltage 

measurement 

terminals

Connect the measurement 

cables 

(p. 26)

.

HIGH terminal: Connect the red cable.
LOW terminal:  Connect the black cable.

  See “Before connecting a measurement cable”(p. 9).

Bottom

Foot

Foot

When mounting the instrument in a rack

Be sure to collapse the feet all the way.

See: “Appx. 7 Rack Mounting” (p. Appx.14)

When using the feet

Be sure to:

 •Open the feet all the way, without stopping partway.

 •Erect both feet.

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DM7275 Series
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands