manualshive.com logo in svg

Hioki DM7275 Series, Instruction Manual

Share
Download
Hioki DM7275 Series Instruction Manual Download Page 30

25

Connecting the Power Cord

2.3  Connecting the Power Cord

Before using the instrument, read “Before connecting a power cord” (p. 8) carefully. 

Connect the power cord to the instrument and a power outlet. 

You will need: The power cord (instrument accessory)

   To outlet

Rear

1

3

4

2

1

 

Turn off the main power switch.

2

 

Verify that the power supply voltage conforms to the instrument’s 

specifications. 

3

 

Connect the power cord to the power inlet on the instrument.

4

 

Connect the cord to the power outlet.

If the power supply is interrupted while the main power switch is in the “ON” position (for example, 

due to a circuit breaker tripping), the instrument will turn on automatically once power is restored.

Power cord

2

Preparing for Measurement

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DM7275 Series
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands