manualshive.com logo in svg

Hioki DM7275 Series, Instruction Manual

Share
Download
Hioki DM7275 Series Instruction Manual Download Page 64

61

 

5

Saving and 

Loading Measurement 

Conditions (Internal Memory)

The current measurement conditions can be saved to the instrument’s internal memory (via the 

panel save function) and loaded from the instrument’s internal memory (via the panel load function) 

as follows:

 • By means of touch panel operation

 • By sending communications commands from an external device

 • By sending signals from an external device

A maximum of 30 panels (with panel numbers 01 through 30) can be saved. Panel data is 

maintained even when the instrument is turned off. 

Measurement conditions can also be saved on a USB flash drive. See “10 Outputting and 

Loading Measurement Conditions (USB Flash Drive)” (p. 120).

Information that can be saved with the panel save function

Save time and date

Measured value 

display

Range selection

Input resistance 

selection

Number of display 

digits

Integration time

Smoothing

Trigger settings 

(measurement count 

and delay)

NULL

Temperature 

compensation

Scaling

Contact check

Comparator

BIN

Absolute value 

judgment

Auto-hold

Label display

Sub-display

5  Saving and Loading Measurement Conditions (Internal Memory)

5

Saving and Loading Measurement Conditions (Internal Memory)

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DM7275 Series
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands