manualshive.com logo in svg

Hioki DM7275 Series, Instruction Manual

Share
Download
Hioki DM7275 Series Instruction Manual Download Page 17

11

Operating Precautions

Before making a connection to the USB connector

 CAUTION

 • To avoid equipment failure, do not disconnect the USB cable while communications 

are in progress.

 • Use a common ground for both the instrument and the computer. Use of different 

ground circuits will result in a potential difference between the instrument's ground 

and the computer's ground. If the USB cable is connected while such a potential 

difference exists, it may result in equipment malfunction or failure.

Before connecting to the RS-232C or GP-IB connectors

 CAUTION

 • Use a common ground for the instrument, computer and programmable controller. 

Use of different ground circuits will result in a potential difference between the 

instrument's ground and grounds of the computer and programmable controller. If the 

communications cable is connected while such a potential difference exists, it may 

result in equipment malfunction or failure.

 • After connecting the communications cable, tighten the screws on the connector 

securely. Failure to secure the connector could result in equipment malfunction or 

damage.

Before connecting a USB flash drive

 CAUTION

 • Inserting a USB flash drive upside down, backwards or in the wrong direction may 

damage the USB flash drive or the instrument.

 • Some USB flash drives are susceptible to static electricity. Exercise care when using 

such products because static electricity could damage the USB flash drive or cause 

malfunction of the instrument.

With some USB flash drives, the instrument may not start up if power is turned on while the USB 

flash drive is inserted. In such a case, turn power on first, and then insert the USB flash drive. 

It is recommended to try out operation with a USB flash drive before starting to use it for actual 

measurements.

Before switching the current sink (NPN) / current source (PNP)

 CAUTION

 • Never switch between NPN and PNP while the instrument's power is on.

 • Configure the NPN/PNP setting based on the externally connected device.

10

9

8

7

6

5

4

3

2

1

Appx.

Ind.

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DM7275 Series
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands