manualshive.com logo in svg

Hioki DM7275 Series, Instruction Manual

Share
Download
Hioki DM7275 Series Instruction Manual Download Page 65

62

Saving Measurement Conditions (Panel Save Function)

5.1 

Saving Measurement Conditions (Panel Save 

Function)

The panel save function saves the current measurement conditions in the instrument’s internal non-

volatile memory. You can select whether to save NULL values. 

(Measurement screen) 

MENU

 > 

PANEL

1

 

Select a panel number.

2

 

3

 

Select whether to save NULL values. 

Checked

Saves NULL values.

Not checked

Does not save NULL values.

4

 

(When saving to an unused panel number)

If you chose 

OK

 

⇒

 Proceed to Step 

5

.

(When saving to a panel number that has 

already been used)

Touch 

OK

 to overwrite the previously 

saved data with the current measurement 

conditions. 

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DM7275 Series
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands