manualshive.com logo in svg

Hioki DM7275 Series, Instruction Manual

Share
Download
Hioki DM7275 Series Instruction Manual Download Page 126

125

11

External Control (EXT I/O)

The EXT I/O connector on the rear of the instrument provides the following functionality:

 • Outputting signals such as the measurement complete signal (EOM signal) and judgment results 

signals (HI, IN, LO) from the instrument to an external device

 • Controlling the instrument by inputting signals such as the TRIG and KEY_LOCK signals from an 

external device. 

Outputting or inputting signals

All signals are isolated from the instrument’s measurement circuitry and from ground (but share a 

common potential with the input and output common pins). 

The instrument’s input circuitry can be switched to support either current sink output (NPN) or 

current source output (PNP) (p. 126). Connect the instrument to a control system after reviewing 

the input and output ratings, internal circuit architecture, and safety precautions (p. 12), and be 

sure to use the instrument as designed.

11.1 

External Control Measurement Process

Preparations

(1) 

Check the input and output specifications of the external device that you are connecting 

to the instrument.

(2) 

Configure the instrument’s NPN/PNP switch. (p. 126)

(3) 

Connect the external device to the instrument. (p. 127)

(4)  Configure external input and output on the instrument. (p. 136)

(5) 

Test input and output. 

(p. 138)

Measurement

Connect the instrument to the measurement target and perform measurement.

11 External Control (EXT I/O)

External Control (EXT

 I/O)

11

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DM7275 Series
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands