manualshive.com logo in svg

Hioki DM7275 Series, Instruction Manual

Share
Download
Hioki DM7275 Series Instruction Manual Download Page 130

129

Connections (Instrument and Control Device)

The connector frame is connected to the instrument’s rear panel (metal portion) as well as the 

power supply inlet’s protective ground terminal. 

When loading panel data by means of a command or touch panel operation, fix pins 4, 5, 22, 23, 

and 24 to ON or OFF (so that they are all either open or all shorted).

For more information about checking EXT I/O input and output, see “11.5 Input Test/Output Test” 

(p. 138).

Signal functions

(1) 

Isolated power supply output

Pin

Signal

NPN/PNP switch setting

NPN

PNP

8

ISO_5V

Isolated power 5 V

Isolated power supply -5 V

9, 27

ISO_COM

Isolated power supply common Isolated power supply common

(2)  Input signals

Signal

Description

For more information

TRIG

 •The instrument operates at the TRIG signal’s ON edge.
 •Operation varies depending on the trigger source.

When the trigger source is 

EXTERNAL

: Measurement is 

performed the set number of times. 

When the trigger source is 

INTERNAL

: The TRIG signal is 

ignored.

 •Measurement must be delayed (by the delay time) after switching 

ranges or loading panel data in order for measured values to 

stabilize. The delay time varies with the measurement target.

“3 Starting 

Measurement” 

(p. 37)

 •When automatic output is set to 

ON

,  the measured value being 

held internally will be output immediately after TRIG signal input.

“9 Data Output 

Settings” (p. 113)

PRINT

By turning on the PRINT signal, it is possible to print the measured 

value and judgment result that are current as of the signal’s edge.

“12 Printing” 

(p. 147).

KEY_LOCK

When the KEY_LOCK signal is on, all instrument key operations 

and touch panel operations (except operation to cancel the key-

lock state) are ignored.

“7 Key Lock 

(Disabling Instrument 

Operation)” (p. 87)

LOAD0 to 

LOAD4

 •Inputting the LOAD signal corresponding to the desired panel 

number for 10 ms will cause that panel to be loaded. Do not 

change the LOAD signal until the load or switching operation is 

complete. LOAD0 is the LSB, while LOAD4 is the MSB.

 •The TRIG signal is ignored while panel load operation is being 

performed. 

 •The LOAD signal is valid even when the instrument is being 

controlled using communications commands (i.e., when the 

instrument is in the remote state).

 •All key operations and touch panel operations are ignored while 

the LOAD signal for a panel number for which settings have been 

saved is on. 

 •When loading panel data by means of a command or touch panel 

operation, fix pins 4, 5, 22, 23, and 24 to ON or OFF (so that they 

are all either open or all shorted).

 •“(4) Signal table” 

(p. 132)

 •“5.2 Loading 

Measurement 

Conditions (Panel 

Load Function)” 

(p. 64)

IN0, 

 

IN1

These pins can be used as general-purpose input pins to monitor 

the status of input with the 

:IO:INPut?

 command.

Communication 

Command Manual 

on the included 

application disc.

0Input signals are ignored while the Measurement screen is not being displayed and while errors 

and other messages are being displayed. 

External Control (EXT

 I/O)

11

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DM7275 Series
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands