manualshive.com logo in svg

Hioki DM7275 Series, Instruction Manual

Share
Download
Hioki DM7275 Series Instruction Manual Download Page 143

142

Timing Chart

Output signal status when the instrument is turned on

Once the display switches from the Startup screen to the Measurement screen after the instrument 

is turned on, the EOM signal will turn on. If EOM output is set to 

PULSE

, the EOM signal will 

remain off. 

ON

EOM

HI, IN, LO, ERR

OB, BIN0 – BIN9

TRIG

ON/OFF

OFF

ON

OFF

OFF

ON

Instrument operation

The instrument’s power is turned on.

Startup screen

Measurement screen

The above chart depicts instrument operation when the trigger source is set to 

EXTERNAL

 and EOM output is 

set to 

HOLD

.

Measurement process (starting measurement from an external device 

and loading judgment results)

This section describes the measurement process from the start of measurement to the acquisition 

of judgment results when inputting the trigger from an external device. 

The instrument will output the EOM signal immediately once the judgment result (HI, IN, LO, 

ERR, or BIN) is finalized. If the connected external device’s input circuitry is characterized by a 

slow response, it may take time for the judgment result to be captured after the EOM ON signal is 

detected.

HI, IN, LO, ERR, BIN

EOM wait 
(for level 
detection, 
after 0.5 ms)

Measurement 

starts

Judgment 

results off

Measurement 

starts

Measurement 

in progress

Measurement 

complete

Measurement 

complete 

received

Measurement 

results loaded

Instrument

Connected external device

TRIG

EOM

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DM7275 Series
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands